Viconics VT7200 Installation Manual (Current Release 5000 S Bedienungsanleitung

1 | PIR Ready VT7200 Series-Installation Guide CONTENTS Installation 2 Location 2 Installation 2 Configurable BI/UI inputs overview 3 Model

10 | PIR Ready VT7200 Series-Installation Guide Pressure dependent VAV cooling / heating with changeover and reheat: VT7200C5x00(x) Floating actuato

11 | PIR Ready VT7200 Series-Installation Guide Schematic Wiring Settings Heating or cooling hydronic valve control: VT7200C5x00(x) Floating actuator

12 | PIR Ready VT7200 Series-Installation Guide Cooling / heating with changeover hydronic valve control: VT7200F5x00(x) Analog actuator Mandatory

13 | PIR Ready VT7200 Series-Installation Guide Wiring examples of 2 remote room sensors for averaging applications: Wiring examples of 3 remote ro

14 | PIR Ready VT7200 Series-Installation Guide seconds after changes are made, the display will resume automatic status display scrolling

15 | PIR Ready VT7200 Series-Installation Guide Zoning Models When heating & reheat is ON, the HEAT LED will illuminate When cooling is ON, the

16 | PIR Ready VT7200 Series-Installation Guide Occupied setpoints adjustments Unoccupied and stand-by setpoints adjustments Setting of the stand-by

17 | PIR Ready VT7200 Series-Installation Guide access to all configuration properties of the Terminal Equipment Controller. Entering a wrong passwor

18 | PIR Ready VT7200 Series-Installation Guide PAN ID Personal Area Network Identification Default value = 0 Range is: 0 to 500 Conditional par

19 | PIR Ready VT7200 Series-Installation Guide Get From Terminal Equipment Controller Get From another device configuration utility Default value =

2 | PIR Ready VT7200 Series-Installation Guide INSTALLATION Remove the security screw on the bottom of Terminal Equipment Controller cover.  Op

20 | PIR Ready VT7200 Series-Installation Guide BI 1 Binary input no.1 configuration Default value = None (None): No function will be associated wi

21 | PIR Ready VT7200 Series-Installation Guide  (Filter): a backlit flashing Filter alarm will be displayed on the Terminal Equipment Controller L

22 | PIR Ready VT7200 Series-Installation Guide Lockout Keypad lockout levels Default value = 0 No lock USER KEY FUNCTIONS LEVEL 0 1 2 NOT U

23 | PIR Ready VT7200 Series-Installation Guide St-By TM Stand-by Timer value Default 0.5 hours Time delay between the moment where the PIR cover det

24 | PIR Ready VT7200 Series-Installation Guide Pband Proportional band setting Default is : 3 Adjust the proportional band used by the Terminal Equ

25 | PIR Ready VT7200 Series-Installation Guide Set Type Temporary setpoint enable Default is : Permnent Enables temporary setpoints feature to

26 | PIR Ready VT7200 Series-Installation Guide aux cont Auxiliary contact function & configuration Default value = 0 Not Used 0 Aux contact func

27 | PIR Ready VT7200 Series-Installation Guide RA/DA Reverse acting or Direct acting signal for Analog output signals VT72xxF5x00(x) models only

28 | PIR Ready VT7200 Series-Installation Guide SPECIFICATIONS Terminal Equipment Controller power requirements: Operating conditions: Storage con

29 | PIR Ready VT7200 Series-Installation Guide DRAWING & DIMENSIONS Viconics Technologies Inc. Tel.: Fax: Toll free:www.v

3 | PIR Ready VT7200 Series-Installation Guide 13. Re-install the cover (top side first) and gently push extra wire length back into the hole in the

4 | PIR Ready VT7200 Series-Installation Guide Binary input #2 can be configured for the following functions: 1. (None): No function will be associa

5 | PIR Ready VT7200 Series-Installation Guide 4. (COS) Change over analog sensor: Used for hot / cold air / water change over switching in 2 pipe s

6 | PIR Ready VT7200 Series-Installation Guide Network ready  All Viconics VT7200 series Terminal Equipment Controllers are designed for stand-alon

7 | PIR Ready VT7200 Series-Installation Guide Wiring Main outputs wiring Single output applications Dual output applications On-Off control VT7

8 | PIR Ready VT7200 Series-Installation Guide Analog control VT7200F5x00(x) Typical applications Schematic Wiring Settings Pressure dependent V

9 | PIR Ready VT7200 Series-Installation Guide Pressure dependent VAV cooling / heating with changeover: VT7200C5x00(x) Floating actuator Mandatory